Saturday, April 19, 2008

Grapewood Candelabra



The other day I stopped by the Fifth Avenue outpost of Japanese retailer Takashimaya for some inspiration. They have a floral studio up on the sixth floor and there are always some interesting creations on display. What caught my eye was a single Grapewood Branch with a number of tea lights perched on it, seemingly defying gravity - simple and intriguing, just the way I like things. Question is, how the heck did they get the tea lights to stay on there? Did they glue them directly onto the branches? Sure, that would work, but cleaning the holders would be very difficult. The best solution would allow the tea light holders to be easily removed. I spent about an hour poking around Jamali Garden looking for a ready-made solution, when it hit me: tea light holders + glue + roofing nails + holes drilled in Grapewood Branches = solution! And doing it this way would allow me to use any vessel, such as bud vases. I got to work. 



Supplies and Materials:
  • 2-3 of the 18-24" Grapewood Branches
  • Tea Light Holders, Bud Vases (or whatever small vessel you like);
  • 1" Roofing Nails (these have large heads); 
  • Super Glue Gel; 
  • Electric Drill with drill bits of various sizes;
  • Wood Screws; 
  • Long Cable Ties.  
The first thing you need to do is arrange your Grapewood Branches in a way that it will make the candelabra as stable as possible. It is rare that you'll find a single Grapewood Branch that's stable in all directions, and this is why you need to use more than one (we used two). Obviously, you do not want this thing tipping over. Try tipping it in every possible direction, and rearrange until you get a stable configuration. Once you've done this, secure the branches together at their contact points with cable ties (a set of pliers would be useful here to pull the cable ties tight). 

Next, it is time to permanently secure the branches together with your wood screws. You'll probably want to drill a small pilot hole through the branches, as Grapewood is fairly hard. We actually used coarse-thread drywall screws, but the bite of these was a bit too aggressive.
  
Now it is time to glue the nails onto your tea light holders, votive holders, or whatever it is you've chosen to use. First, clean the bottom of them. Then turn them upside down, put a dab of the super glue gel on the nail head, and stick it on. The more glue the merrier. The super glue gel sandwiched between the metal heads and the glass takes quite a while to set, so you should leave these overnight. After the glue has had plenty of time to set, give the nails a good wiggle to make sure they are secure - you are likely to have one or two that don't have a strong bond, and now is when you want to find this out - not when you have a lit candle in it or a vase full of water. This is especially important with heavier items, such as bud vases, which when filled with water and flowers will put the most strain on the bond. 

Next up, start drilling the holes into your Grapewood. Pick a drill bit that is just a hair bigger than the nail. As for where to drill, pick spots that are level and drill straight down. This is the trickiest part of the operation. You'll likely end up with a few holes that angle a bit away from vertical, but you'll also have some holders or vases where the nail isn't quite glued on straight - match these correctly (rotate the vase or candle holder), and they will sit (more) level.  

Add your tea lights, votives and/or flowers and you have a stunning and unique centerpiece that will surely get a lot of attention!

7 comments:

Anonymous said...

Other great presentation candelabras are being sold and rented at http://www.candelabrasupply.com. They had a range from wedding candelabras to floor candelabras to different candelabras I haven't seen on other sites.

Anonymous said...

Wow! This is beautiful!

Unknown said...

I loved the look so much that I created a variation on the theme and now sell them at highwood.etsy.com
TIP: by attaching chubby glass votive cups, you can mix and match flickering LED votive candles and orchids.

Unknown said...

Hello! This is amazing! I'd like to ask what are the sizes of the tea holder and vase (in inches, diameter)? Thank you!

Justin said...

Those are just standard tea light holders - 1-2" I believe. The vase is also between 1-2 inches in diameter. Hope this helps!

Anonymous said...

These are beautiful arrangements-where do you get the grapewood?

Justin said...

Glad you like it! We get the Grapewood from Nettleton Hollow of course! http://www.nettletonhollow.com/grapewood.html

The Grapewood is salvaged from commercial table grape vineyards that periodically have to replant their vines.